chore: rename html to php, add donate/payments page, update cv

1 files changed, 0 insertions, 102 deletions

diff --git a/drafts/dell-dock.html b/drafts/dell-dock.html
deleted file mode 100644
index 4a9dd9a..0000000
--- a/drafts/dell-dock.html
+++ /dev/null
@@ -1,102 +0,0 @@
-<h1>Make Your Docking Station Work for You (on FreeBSD)</h1>
-
-<p class="description">
-  I have a Dell Latitude E-series laptop running FreeBSD 12.2-RELEASE. I also
-  have a Dell E-Port II docking station on my desk. I wanted to be able to take
-  my shut, sleeping laptop and plop it down on the docking station, hit the dock
-  power button, and have the laptop wake up and switch over to all of the
-  docking station peripherals. So I did it! And now I'm going to write about it
-  so I don't forget how. You need to know a little bit about FreeBSD
-  <code>sysctl</code> knobs, display outputs in X, sound devices, and
-  <code>ifconfig</code> networking.
-</p>
-
-<h2>Switching from Ethernet to WiFi and Back Again, Seamlessly</h2>
-
-<p>
-  FreeBSD doesn't magically swap from wireless to wired connections by default,
-  but there's an easy way to remedy this: link failover. I recommend reading the
-  <a href="https://www.freebsd.org/doc/handbook/network-aggregation.html"
-    >FreeBSD handbook page on network aggregation</a
-  >
-  as it's where I found out about link aggregation and failover. Basically,
-  aggregation lets you bind two of your network interfaces together into a
-  single virtual interface. Failover lets your traffic continue moving as long
-  as one of the aggregated interfaces has is connected. 
-  Here's what I had to do:
-</p>
-
-<ol>
-  <li>
-    Bind the wireless network interface (wlan0) to the MAC address of the wired
-    interface (em0)
-  </li>
-  <li>Create a lagg interface using the two network interfaces</li>
-  <li>Bind the lagg interface to an IP address, preferably with DHCP</li>
-</ol>
-
-<p>All of this is configured in my <code>rc.conf</code>:</p>
-
-<pre><code>
-wlans_iwn0="wlan0" # <- wlan0 device should use the iwn driver
-ifconfig_wlan0="WPA" # <- wlan0 should use WPA (wpa_supplicant) to connect to wireless SSIDs
-create_args_wlan0="wlanaddr 5c:26:0a:06:c1:d6" # <- wlan0 MAC address is set to em0 device MAC address
-ifconfig_em0="up" # <- enable em0 (ethernet) device
-cloned_interfaces="lagg0" # <- create cloned interface lagg0
-ifconfig_lagg0="up laggproto failover laggport em0 laggport wlan0 DHCP" # <- configure lagg0 interface to act as a failover lagg protocol over em0 and wlan0
-</code></pre>
-
-<p>
-  In practice, the preferred device is <code>em0</code>, or my ethernet NIC.
-  FreeBSD will always try to use that first. If it's disconnected, such as when
-  the laptop is removed from the dock, the wireless device (<code>wlan0</code>)
-  will take over. This transition happens instantly, and without interrupting
-  traffic; active transactions aren't cut short for example.
-</p>
-
-<h2>Sleeping on Lid Close Except When Docked</h2>
-
-<p>
-  This is an easy one. You can use <code>sysctl</code> to configure what happens
-  when a laptop lid is closed. I wanted the lid closing while undocked to
-  suspend (put the laptop to sleep). When it's docked however, I don't use the
-  internal display and wanted to be able to shut the lid and leave it shut. If you read <code>ACPI(4)</code> in the manual, you'll find this little passage:
-</p>
-
-<pre>
-<blockquote>
-hw.acpi.lid_switch_state
-		 Suspend state (S1-S5) to enter when the lid switch (i.e., a
-		 notebook screen) is closed.  Default is "NONE" (do nothing).
-</blockquote>
-<pre>
-
-<p>I changed this value a long time ago so closing the lid suspends the laptop. You can check with <code>sysctl</code>:</p>
-
-<pre>
-<code>
-$ sysctl hw.acpi.lid_switch_state
-hw.acpi.lid_switch_state: S3
-</code>
-</pre>
-
-<p>Now, if I wanted to disable this functionality, I would just change this parameter as root:</p>
-
-<pre>
-<code>
-$ doas sysctl hw.acpi.lid_switch_state=NONE
-hw.acpi.lid_switch_state: NONE -> NONE
-</code>
-</pre>
-
-This change takes effect immediately. I can open and close the lid and nothing happens but turning off the screen. Awesome.
-
-<h2>Swapping Primary Display Outputs (Also Nvidia Screen-Tearing)</h2>
-
-<h2>Switching Default Sound Device</h2>
-
-<h2>Putting It All Together (Scripts Are Glue)</h2>
-
-<h2>What I Didn't Have to Do</h2>
-
-usb devices, battery/charging